tornos usadas para venda (3,093)

This lathe is defective, so repair is necessary, fixed head is supplied separately Auction-ID: A1-48552-60

Lathe with 4 tools only for 3-cylinder crank shaft

weight of the machine ca.:18 tcentre distance:700 mmmax. swing diameter:200 mmLathe with 4 tools only for 3-cylinder crank shaft

weight of the machine ca.:18 tcentre distance:700 mmmax. swing diameter:200 mmLathe with 4 tools only for 3-cylinder crank shaft

max. workpiece diameter:29 mmmin. workpiece diameter:26 mmworkpiece length:66 mmthe system was originally delivered for the following workpiece sizes: diameter 26mm - 29mm length 65mm - 66mmChanging parts in the clamping device, handling, etc. would probably result in diameters of up to approx. Ø50mmTotal length will probably be almost 400 mm possible with a few conversions.Also dependent on tool lengths, machining lengths on the component, etc.Workpiece: Piston pin Drawing number: WHT 000 718, WHT 000 718 A Workpiece dimensions (Ø, WxH): Ø26 x 66; Ø29 x 65 Length: 66 or 65 mm Material: 17Cr3Quantity: xxx parts / year Cycle time: 5 sec. However, workpiece lengths up to 600mm are manageable. The machining diameter can be adjusted if the appropriate tools are available. The clamping station can currently only accommodate this product. However, this can be adapted by changing the clampi ...

turning diameter:250 mmswing diameter:250 mmturning height:200 mmtotal power requirement:37,7 kWchuck diameter:315 mmspindle speed max.:5500 1/mintravel -x axis:625 mmtravel -y axis:+100/-80 mmtravel -z axis:250 mmworktool system:VDI 30+40 weight of the machine ca.:8 tThe synchronous spindle is powered with 37.7 kW of power, a torque of 300 Nm and a maximum speed of 5,500 rpm.Typical components are ball cages, ball hubs, gear wheels, sliding sleeves,pump wheels, flanges, synchronizer rings, bearing rings and pivot pins.The machine bed is made of Hydropol, a mixture of special concrete and steel, which ensures the greatest smoothness and precision even with larger components and powerful machining.

number of spindles:6 spindle passage:18 mmturning length:63/50 mmweight of the machine ca.:8,6 tspindle drive motor:11 kW

turning diameter:200 mmturning height:120 mmweight of the machine ca.:18 tAvailable from 01.08.2024

turning diameter:1000 mmswing diameter:1000 mmMachine type: Vertical latheManufacturer: HessappType: DV 62Serial no.: 14.2308Working range of the spindleLargest diameter 1000 mmLargest swing diameter 1000 mmCross slide travelStroke of the vertical slide 900 mmStroke of the horizontal slide 1810 mmTotal travel 2315 mmTurning spindleSpindle head with centering cone according to DIN 55021 A15Spindle diameter in the front bearing 203 mmMain driveVia a controlled asynchronous motor and gear transmissionwith range switching.Spindle speedsSpeed range I: 5 - 350 rpm.Speed range II: 30 - 1000 rpm.Travel speedX/Z axis: 10 m/min.W1 axis: 8 rpmNo C-AxisTexte, Bilder, Grafiken, Layout, Strukturen und Algorithmen etc. unterliegen weltweitem Urheberrecht.Unerlaubte Verwendung der Daten, werden sowohl strafrechtlich als auch zivilrechtlich verfolgt.Das ausschließliche Urheber- / Nutzungsrecht dieser ...

faceplate diameter:800 mmpower requirement:110 kWweight of the machine ca.:37.000 / total 52.000 ttransport measurements machine:5,07 x 2,98 x 3,90 mclamping diameter:800 mm:Ø 800 x 720 mmTool bore:Capto C6 tools in tool magazin:2 x 80 With C-Axis

faceplate diameter:1600 mmpower requirement:80 kWweight of the machine ca.:25 tdimensions of the machine ca.:4,4 x 4,62 mmax. workpiece diameter:2000 mmmax. diameter of face turning:1800 mmtool taper:ISO50 The machine has been regularly serviced and is in good technical condition. With C-Axis

- Maximum distance between points approx. 6000 mm. - Turning on bed approx. 740 mm. - Flip on carriage approx. 420 mm. - Bed width 510 mm. - Bar pitch diameter approx. 80 mm. - 18 rotation speeds from 16 rpm to 1250 rpm. - 3-jaw chainring, diameter 400 mm. - Fagor 20i-T 2-axis (X,Z) digital display. - Equipped with 2 windows. - Operating conditions of this machine: unchecked. Auction-ID: A7-48839-23

Heidenhain control, Leica microscope Auction-ID: A1-48552-17

turning diameter:270 -300 mmturning length:710 mmtotal power requirement:43 kWweight of the machine ca.:8,5 tdimensions of the machine ca.:3,16 x 2,15 x 2,15 mThe machine does not include a chuck or tools ? the machine was originally purchased without these accessories. The G300 has X, Z, Y, C, SP, and driven tools. A bar feeder can be used, but the machine does not have one.

turning diameter:250 mmswing diameter:260 mmAvailable from October 10, 2025 The system consists of two individual systems that are linked together.No driven tools!

turning diameter:220 mmturning length:310 mmtotal power requirement:17 kWweight of the machine ca.:3,3 tdimensions of the machine ca.:2,25 x 1,63 x 1940 mgreates pass round over bed:430 mmbore diameter:45 mmcentre distance:687 mmslide travel radial ( X-axis ):160 mmslide travel axial ( Z-axis ):310 mmspindle turning speed range:0-6.300 U/min

turning diameter:220 mmturning length:700 / 665 mmtotal power requirement:17 kWweight of the machine ca.:2,6 tdimensions of the machine ca.:2,63 x 1,98 x 1,94 mgreates pass round over bed:430 mmPart length max.:510 slide travel radial ( X-axis ):160 mmbore diameter:45 mmTexte, Bilder, Grafiken, Layout, Strukturen und Algorithmen etc. unterliegen weltweitem Urheberrecht.Unerlaubte Verwendung der Daten, werden sowohl strafrechtlich als auch zivilrechtlich verfolgt.Das ausschließliche Urheber- / Nutzungsrecht dieser Daten wurde nachfolgender Person eingeräumt.Copyright © 2005-2026, Josef Weber. All rights reserved.

turning diameter:360 mmturning length:520 mmtotal power requirement:20 kWweight of the machine ca.:3,8 tdimensions of the machine ca.:3 x 2 x 2 m

turning diameter:360 mmturning length:520 mmtotal power requirement:20 kWweight of the machine ca.:3,8 tdimensions of the machine ca.:3 x 2 x 2 m

12-position turret, 500GH spindle, MORI SEIKI MSD-501II control Excluding machining and tooling supports AVAILABILITY END OF JANUARY/BEGINNING OF FEBRUARY 2027 Auction-ID: A7-49592-14

Mori Seiki ZL 250-600 CNC Lathe Power of the main spindle 18.5 Kw Passage of the main spindle rod 73 mm Diameter of rotation 250 mm Length of rotation 650 mm Number of revolutions of the main spindle 3500 Number of Tool Turrets 2 Number of first turret tool locations 12 Number of motorized first turrets 12 Travel X-axis first turret 238 mm Travel Z-axis first turret 650 mm Number of second turret tool locations 10 Number of fixed tool positions second turret 10 Travel X-axis second turret 173 mm Z-axis travel second turret 650 mm Tailstock Quill stroke 150 mm Chip conveyor Incl. tools in the turret Auction-ID: A7-49053-19

According to photos, weight estimated Auction-ID: A1-48554-211

Specifications: X-axis: 580mm Z-axis: 1045mm Y-axis: 160mm B-axis: 225° C-axis: 360° Machine is equipped with: - milling head - chip conveyor - Mazak Flex GS-150F automatic loading unit - tool setter Auction-ID: A1-49370-21

NAKAMURA-TOME WT-100 CNC turning center equipped with an LNS Quick Load Servo II bar feeder, enabling efficient automated mass production. This complete installation combines: Dual spindle Double turret Automatic bar feeding It enables continuous production of parts without operator intervention, which greatly reduces cycle times and increases productivity. Ideal for: CNC turning workshops Bar turning Serial and medium-series production Industrial subcontracting Precision mechanics The LNS feeder is a recognized benchmark for CNC lathe automation, highly sought after in combination with a Nakamura-Tome machine. Auction-ID: A1-48554-6

Machine is equipped with: - Live tooling - chip conveyor - tailstock - 2 live tools as seen in picture - set of 12 tools (may differ from photo’s) Auction-ID: A1-49370-18

DL-35M motorized turret, FANUC Series Oi-TF control Excluding machining and tooling supports AVAILABILITY END OF JANUARY/BEGINNING OF FEBRUARY 2027 Auction-ID: A7-49592-13

: 0330 mm: 210 mm: 1000 mm: 167 mm: 40 mm: 2,2 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 0330 mm: 210 mm: 1000 mm: 167 mm: 40 mm: 2,2 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Auction-ID: A1-49370-10

Distance, max between tip 950 mm approx, mandrel diameter: 300 mm Auction-ID: A1-48824-67